Genuine OEM-quality parts — +90 444 4 970  |  WhatsApp
100. Yil Bulvari No: 44, Ostim, Ankara 06370, Turkey
Mon-Fri 08:00-18:00 (GMT+3) +90 444 4 970
8A31-54-1110 OEM PARTS SPECIALIST
Call WhatsApp
Installation Guide

How to Install 8A31-54-1110

Komatsu Komatsu D85/D155 Cabin Mount — Komatsu D85AX-15, Komatsu D155AX-5

Before You Begin

Installing 8A31-54-1110 requires a trained technician, calibrated tools, and the official Komatsu service manual. Est. time: 30–90 min.

  • Skill level: Trained technician
  • Calibrated torque wrench required
  • Two-person lift may be required

Related: Also review the Komatsu 8A31-54-1130 installation guide if servicing the full assembly.

Step-by-Step Procedure

1

Safety First

Park on level ground, engage brake, chock wheels. Disconnect battery negative. Depressurize hydraulic system to 0 bar before starting work.

2

Gather Tools

Calibrated torque wrench, metric socket set, rubber mallet, penetrating oil, anti-seize compound, lint-free rags, safety glasses and gloves.

3

Access the Component

Locate komatsu d85/d155 cabin mount per Komatsu service manual for your serial number. Consult the parts diagram for exact mounting locations.

4

Remove Old Part

Apply penetrating oil 15 min before removal. Remove fasteners in cross-pattern. Support the assembly before removing the final fastener.

5

Inspect Surfaces

Clean seating surfaces. Check for cracks, corrosion, or thread damage. Inspect for frame fatigue cracks near mounting bosses.

6

Install 8A31-54-1110

Position 8A31-54-1110 correctly — check orientation markings. Insert fasteners hand-tight. Confirm correct seating.

7

Torque to Specification

Cabin mount bolts require precise torque. Under-torquing allows micro-movement and fretting corrosion. Over-torquing compresses the rubber element and eliminates vibration damping. Always use a calibrated torque wrench.

8

Function Test

Reconnect battery. Idle 5 min. Check for leaks or unusual vibration. Test under light load before returning to full service.

Installation Tips & Torque

  • Support the cab with a floor jack before removing any mount
  • Mark each mount position before removal to ensure correct reinstallation
  • Clean seating surfaces and check for frame cracks before installing new mounts
  • Torque in two passes: 50% then full torque in cross-pattern

Cabin mount bolts require precise torque. Under-torquing allows micro-movement and fretting corrosion. Over-torquing compresses the rubber element and eliminates vibration damping. Always use a calibrated torque wrench.

FAQ

How do I know my cabin mount needs replacement?

Signs include increased cab vibration and noise, visible rubber cracking, cab sitting lower or at an angle, or failed bounce test (cab doesn't return to center after pushing).

Can I use aftermarket cabin mounts?

Generic aftermarket mounts often differ in durometer (Shore A hardness) and rubber compound. This causes early failure or inadequate isolation. Use OEM-spec parts.

Order 8A31-54-1110 — Fast Worldwide Shipping

ISO 9001:2015 certified OEM-quality parts. Ships from Ankara. 24-hour quote worldwide.

View on Babacankaucuk.com WhatsApp Quote Call +90 444 4 970

Required Tools — Complete Checklist

Have all tools verified and calibrated before starting. A missing or uncalibrated tool is the most common reason installers improvise and cause damage to the new part.

  • Calibrated torque wrench (0–300 Nm range)
  • Metric socket set (10–24 mm, 1/2" drive)
  • Hydraulic floor jack rated ≥5 tonnes
  • Jack stands, minimum 2, rated for load
  • Penetrating oil (e.g., PB Blaster or equivalent)
  • Wire brush and thread tap set
  • Anti-seize compound
  • Lint-free rags and degreaser
  • Safety glasses, steel-toed boots, mechanic’s gloves
  • Komatsu service manual (correct serial number edition)

Common Installation Mistakes to Avoid

These are the most frequent technician errors that cause repeat failures after installation of 8A31-54-1110:

  • Over-torquing mounting bolts — compresses the rubber element and eliminates vibration isolation
  • Installing mounts in wrong positions (front/rear mounts may have different load ratings)
  • Skipping the support jack — dropping the cab onto a new mount during installation damages the rubber bond
  • Reusing corroded mounting bolts — they may not achieve the required clamp load and can fail under vibration
  • Mixing old and new mounts on the same machine — uneven spring rates create cab lean and overload the new mounts

Post-Installation Verification Checklist

  • All fasteners torqued to specification — verified with calibrated wrench
  • All guards, covers, and safety systems reinstated
  • Battery reconnected and hydraulics repressurised gradually
  • Engine idled for 5 minutes — check for leaks or unusual noise
  • Light-load test before returning machine to full duty cycle
  • Installation date, part number, and machine hours logged in service record
  • 50-hour re-inspection scheduled in the maintenance calendar